To upgrade the 4-way of your 1999 Camplite Damon Model 2408sle to a 7-way so that you can use the brakes of the trailer you'd want to use the Epicord 7-Way with Junction Box part # 277-000141. You'd cut off the 4-way of you trailer and run it to the matching posts of the junction box and then run 10 gauge wire like part # 10-1-1 from the brake output pin of the box to the brake assemblies and you'd be set. view full answer...
The Optronics # A44RB Replacement Red Lens fits your MCL40RB light fixture. If you need an amber lens you can order the Optronics # A44AB. It is Department of Transportation approved and SAE certified. view full answer...
The best cover we have for a 2017 Livin' Lite 11FK is the Adco SFS AquaShed Cover for Travel Trailer part # 290-52238 which has zippered panels for access to the entry door. It would be a little large but there's no avoiding that as this is the smallest cover we offer for travel trailer's. The excess material can be tied off however with the integrated cinching system so you won't have any problems. view full answer...
The Alpha Systems Superflex RV Roof Membrane with Installation Kit, # AL37UV is not designed for canvass tent material used with pop-up style campers but over the top of solid roofs.
The Camco Pro-Tech Patch Kit for RVs w/ Rubber Roofs, # CAM41461 has been used successfully on the fabric of pop-up campers. view full answer...
Water heaters, including the tankless options from Furrion, are not specific fits for any one trailer, so what you'll have to do is take a couple measurements to see if the correct option is indeed the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door # FR98SR.
The first measurement you need to take is the compartment where the heater fits, and it needs to be at least 12-5/8" wide x 12-5/8" tall x 19-1/4" deep, which is the size of the heater itself.... view full answer...
We may have what you're looking for, for your 2014 Livin Lite Quciksilver, however to be certain I would need to know the size of window you're replacing.
For instance, we have the:
-Replacement RV Entrance Door Glass # VAL58GR which fits beautifully with the Valterra Entry Door Window Frame Assembly # A77051.
This window measures 12 1/2" wide and is 21 1/2" tall, so if this is the size of window you're needing then this'll work great for you.
If not, let me know what you need and... view full answer...
The Dexter 3,000 lb hubs use inner bearing # LM67048, outer bearing # L44649, and double lip grease seal # 58846. We don't have all of these together in a kit but you can order them individually and you'd be set. view full answer...
You are correct that these two hub and drums are exactly the same but one has a standard grease cap and the other has an E-Z Lube grease cap for E-Z Lube spindles, so both will fit 12" to 15" wheels. The correct one for you will simply depend on if you have an E-Z Lube axle or not:
- Dexter Trailer Hub and Drum Assembly for 2,000 lb E-Z Lube Axles # 8-257-5UC3-EZ
- Dexter Trailer Hub and Drum Assembly for 2,000 lb Axles # 8-257-5UC3 view full answer...
I am not sure which vent these trailers use but what you can do is go with a universal cover like the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent part # MA00-335001 for white or part # MA00-335002 for smoke. If you don't want to go with universal then you'll need to know you vent model number found on the sticker inside the frame. view full answer...
The 12-volt trailer feed, which is the pin that sits in the 1:00 position if you're looking at the front face of the 7-way connector on the vehicle is fed by the vehicle battery. If this connection isn't already made on the vehicle side, run a length of 10 gauge wire like # 10-1-1 which is sold by the foot from the 1:00 terminal to the vehicles positive battery terminal. You'll run that circuit through a 40 amp breaker like # 9510.
On the trailer side, you'll run the battery circuit from... view full answer...
For your Dexter torsion axle that has a 2,000 lb capacity the correct lift kit is the part # K71-723-01 for each axle. This will give you a lift of 2-5/8 inches. view full answer...
The tire that comes with Karrier ST205/75R15 Radial Trailer Tire with 15" Aluminum Wheel - 5 on 4-1/2 - Load Range C # AM32404 has a speed rating of M or 81 MPH. view full answer...
The correct lift kit for a Livin’ Lite Quicksilver 8.5x30 with Dexter Torflex #12 Axles is the Torflex Lift Kit part # K71-725-02. I was able to confirm this for you by calling Dexter with your axle's serial number. That said, this will hold true for any trailer with a Dexter Torflex #12 Axle usually depicted as T12 on the axle tag. view full answer...
Yes, the etrailer.com Trailer Tongue Weight Scale part # e99044 will work well to determine the tongue weight of your setup so that you can get a properly rated weight distribution system for your trailer. When choosing a weight distribution system you do want to chose spring bars that have a tongue weight rating that your tongue weight falls in the middle of.
For example, Equal-i-zer Weight Distribution System w/ 4-Point Sway Control part # EQ37100ET is rated for trailer tongue weights... view full answer...
I recommend Adco Olefin All-Climate + Wind RV Cover for Travel Trailer - Up to 22' Long - Gray part # AD47ZR for the 2016 Livin Lite CampLite Travel Trailer. The Adco Olefin top will keep the roof of your Livin Lite trailer protected from harmful UV rays that can cause dry rot on other covers. I have attached a video for your reference.
As far as being able to walk on the roof of the travel trailer that is something that really depends on the amount of roof support the trailer has. I... view full answer...
The Torflex Lift Kits like part # K71-707-02 do come with a protective painted black finish. As mentioned, the paint can chip if not careful. That said, the finish is not really crucial for most applications which is why the paint is not as durable. However, since you have an aluminium frame trailer it might be best for you to either send the lift blocks off for powder coating or simply apply a few more coats of paint yourself. Once this is done, I'm sure they will be just perfect for you... view full answer...
The Reese Pole-Tongue Adapter # RP58393 will allow you use the Blue Ox TrackPro Weight Distribution # BLU36FR. You will need this as the Blue Ox Adapter # BXW4023 is only compatible with their SwayPro style system which uses chain hangers. view full answer...
You need the Replacement Dome for Fan-Tastic Vent RV Roof Vents, # FVK1020-19, it fits models FV801200, FV801208, FV801250, FV807350, FV802250, FV803350, and FV800900.
I suggest you also consider one the Ultra Breeze vent covers, # FVU1500WH, or # DMC38FR to give you the ability to utilize your fan and vent in all weather conditions and even when towing. It will also protect that Lid from damage. view full answer...
I have a solution for you but we don't have a replacement lens in those dimensions. For an exact replacement part you would need to check with your trailer's manufacturer.
You spoke of wanting to replace the porch light and read reviews, the closest light we have to the 2-1/4" x 4-13/16" dimensions is going to be the Low Profile LED Utility Light item # 328-007-61W. This is a 5-5/8" x 3-1/8" warm white LED light. It will provide 204 lumens of light and is far more efficient than your... view full answer...
Go To Results